1. Mischen von Henan Litefeuerfeste Feuerbetone: it is necessary to use forced mixer or mortar mixer to mix materials, manual mixing is not available. Equipment and things: compulsory or mortar mixers, buckets, scales, shakers, shovels, trolleys, etc. Mixing: Put the big bag of material in the mixer first, then the small bag of material, dry mixing for 1-2 minutes, then the material can be discharged for pouring. Judgment method of water content: In order to judge whether the water content of the mixing material is suitable, a simple "hand kneading into a ball" method can be selected for testing: if the pellet is deformed and flows out from the hand seam, it indicates that the water content is too much: if If the pellets are cracked and scattered, it indicates that the water content is too low. Mixing water consumption: take the water consumption given in the instruction manual of the batch of products as the standard, strictly control the water consumption and accurately measure it.
Note: ① The things used in the construction process, such as mixers, buckets, shovel, etc., should be cleaned up in advance, and lime, gravel, Portland cement and other sundries should not be mixed in. ②The water used for mixing must be clean tap water. Under the condition that the slurry can be shaken out, use as little water as possible to achieve a better construction effect. ③The mixing amount is not easy to be too much each time, it should be determined according to the type of the mixer, otherwise it will cause the mixer to get stuck and stop. The remaining agglomerated block material cannot be mixed with water again. ④The temperature of the construction site must be between 5 and 30 degree . If the temperature on the construction site is lower than 5 degree , it is necessary to adopt corresponding heating protection measures before construction: if the temperature on site is higher than 30 degree , it is necessary to choose corresponding cooling protection The method can be used for construction: otherwise, the product will be difficult to construct or its function will be reduced.
2. Die Gießkonstruktion von Henan Litefeuerfest gießbar: Kontrolle: Vor der betonierbaren Konstruktion muss kontrolliert werden, ob die Anker fest verschweißt sind, und für Teile über 500 Grad sollten hitzebeständige Haltenägel verwendet werden. Die Außenfläche der Anker sollte mit 0,5-1 mm dicker Farbe gestrichen oder mit Plastikband umwickelt werden, um die Expansionskraft nach dem Erhitzen zu dämpfen und Schmutz aus der Form zu entfernen. Gießkontrolle im Moment: Die neu angemischte Gießmasse sollte zügig gegossen werden, und das Gießen sollte in der Regel innerhalb von 20 Minuten abgeschlossen sein. Gießen: Gießen Sie das gemischte Gießmaterial in die Form und stechen Sie den Vibrationsstab rechtzeitig durch, um zu vibrieren. Die Vibration muss gleichmäßig sein. Bewegen Sie bei fließendem Schüttgut den Rüttelstab mit einer Geschwindigkeit von 1-2 m/min. Beim Herausziehen des Schüttlers sollte die Geschwindigkeit langsam sein. Nach dem Gießen müssen die Anforderungen an die Standorttemperatur kontrolliert werden: Nach dem Gießen und vor dem Kondensieren muss die Standorttemperatur über 5 Grad (5-30 Grad) gehalten werden, und die Standorttemperatur muss unter 5 Grad liegen. Es ist notwendig, entsprechende Methoden zum Schutz vor Temperaturanstieg anzuwenden, da es sonst zu einer Verlangsamung kommt. Kondensation, die zu einer Beeinträchtigung der Produktfunktion führt.
Note: ①The appearance of the castable after the sensation should be kept, and it is not suitable to use things to polish it, and it is not allowed to sprinkle cement powder on the surface to polish it. ② The oscillating bar must be backed up to prevent the backup bar from being activated in time when the oscillating bar fails. ③After the completion of construction, within 24 hours of the construction body, especially before the castable is hardened, it is strictly forbidden to move, stir or ram, otherwise, cracks and even complete destruction of the pouring can occur. ④ The castable should be constructed in succession. When the continuous construction is not possible due to various reasons, the construction joints can be left and left at the expansion joints, otherwise the construction joints will be pitted, that is, a cross with a depth of 10mm and a width of about 20mm is drawn on the castable. Ditch, the distance is about 100mm.
3. Wartung von Henan Litefeuerfeste Feuerbetone: Dinge: Polyethylen-Kunststofffolie, Strohsäcke usw. Umgebungstemperaturanforderungen und Handhabung: Die Haltetemperatur des Gießkörpers sollte zwischen 15 und 35 Grad liegen. Wenn es diesen Temperaturbereich überschreitet, sollten entsprechende Heiz- oder Kühlmethoden angewendet werden, da es sonst zu einer Verringerung der Verwendung des Produkts kommt. Wartung: Nachdem das Betonmaterial ausgehärtet ist, muss die Oberfläche der Konstruktion sofort mit einer Polyethylen-Kunststofffolie abgedeckt und dann ein feuchter Grassack darauf gelegt werden, um das Eindringen von Wasser zu verhindern und die Zementaktivierung zu fördern. Hören Sie nach dem Aushärten innerhalb eines Tages auf zu schlagen und zu fühlen. Je nach Aushärtungszustand kann die Form nach 24-30 Stunden Aushärtung entfernt werden. Pflegen Sie die Form nach dem Entfernen nach Bedarf 2 Tage lang und decken Sie sie während der Wartung weiterhin mit Polyethylen-Kunststofffolie und nassen Grassäcken ab. Nach 3 Tagen Oxidation wurden die Polyethylen-Kunststofffolie und der nasse Strohbeutel entfernt. Den Gießkörper 1 Tag an der Luft trocknen lassen, dann kann er gebacken werden.